Mircom TX3 Series Manuale di Installazione Pagina 71
- Pagina / 122
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
NSL Relay Cabinet Installation and Wiring
Version 3.2
Telephone Access System Installation and Operation Manual
71 (122)
LT-969 Copyright 2015
5.3.2 Switches
SW1. Turns the unit’s power ON and OFF for servicing, or to re-start the unit.
SW2. Not used.
5.3.3 Jumpers
JW1. JW1 is used for updating firmware and is normally open.
JW2. JW2 is used for updating firmware and is normally open.
All other jumpers are not used.
5.3.4 Telephone Line
Each NSL control unit provides a single telephone line connection to the Lobby
Control Unit. See Figure 40 and Figure 41.
Each Lobby Control Unit panel can use any one of the five telephone lines on the
Lobby Control Unit Main Controller Board to communicate to an ADC
telephone system or to an NSL relay control unit.
There are many possibilities for connecting Entry Control panels and NSL
control units, but each main Lobby Control Unit requires one individual
telephone line to each NSL control unit.
Lobby Control Units connect to the NSL and control units through telephone
lines. Telephone lines are not connected to expansion units.
Expansion relay control units do not require an individual telephone line.
- TX3 Series 1
- Contents 3
- List of Figures 5
- List of Tables 7
- Introduction 9
- 1.1 TX3 Systems 10
- 1.2 Features 11
- 1.3.1 Universal Series 12
- 1.3.3 Universal Slim-Line Kit 13
- 1.3.4 Continental Series 14
- 1.3.5 Kiosk Free Standing 15
- 1.6 About This Manual 16
- 1.7 Contact Us 17
- 1.7.3 Website 18
- 1.7.4 Email 18
- 1.7.5 Technical Support 18
- Enclosure Installation 19
- 2.3 Installing the Heater 26
- 50.117 " 27
- 17.950 " 27
- 14.187 " 27
- Bolts (x4) 28
- Reinforcement Bracket 28
- Nuts (x6) 28
- Bolts (x8) 29
- Base Plate 29
- Kiosk Mounting Holes (x12) 29
- TX3 System 33
- 3.1 TX3 System 34
- 3.2 Single Lobby Control Unit 35
- ADC line and four NSL lines 36
- 3.3 Dual Lobby Control Units 37
- 3.6 Networking TX3 Panels 41
- 3.7 Lobby Control Unit Wiring 44
- Lobby Control Unit Setup 45
- 4.1 Controller Board 46
- 4.1.1 Connectors 47
- 4.1.2 Potentiometer 47
- 4.1.3 Switches 47
- 4.1.4 Jumpers 47
- 4.2.1 Microphone Connection 48
- 4.2.2 Speaker Connection 48
- 4.2.3 Inputs 1 to 5 48
- 4.2.4 RS-485 50
- 4.2.5 Auxiliary Camera Supply 50
- 4.2.6 LED/Lamp Supply 50
- Note: Use 18 AWG 51
- 4.3.1 Telephone Lines 1 to 5 52
- 4.3.2 JW8 52
- 4.3.4 AC Output Door Strike 53
- 4.3.5 DC Output Door Strike 53
- 4.4 Modem Board 54
- 4.5 MD-921 IP Module 55
- 4.6 MD-993 Module 56
- 4.7 Guard Phone Module 57
- 4.8 Guard Phone 57
- 4.9 Controller ID Setup 58
- 4.10 Configuration Using a PC 61
- 4.11 Updating Firmware 62
- 4.12 Beginning Configuration 62
- 65 (122) 65
- Figure 36. NSL Relay Cabinet 66
- 67 (122) 67
- TX3-NSL-8M Relay Control Unit 68
- NSL Main Controller 68
- NSL Backplane Board 68
- 1535 relays 69
- 5.3.1 Connectors 70
- 5.3.2 Switches 71
- 5.3.3 Jumpers 71
- 5.3.4 Telephone Line 71
- TX3 Lobby Panel Main 72
- Controller Board 72
- 73 (122) 73
- 75 (122) 75
- Jumper Setting 76
- Backplane Number 76
- Selection 76
- 77 (122) 77
- 78 (122) 78
- This connector mounts 79
- Amphenol connection 79
- 80 (122) 80
- 81 (122) 81
- 82 (122) 82
- 83 (122) 83
- 84 (122) 84
- 85 (122) 85
- 5.4 Updating Firmware 86
- Elevator Restriction Unit 87
- Installation 88
- 89 (122) 89
- 90 (122) 90
- 91 (122) 91
- 6.3.2 Connectors 92
- 6.3.3 DIP Switches 92
- 6.3.4 Jumpers 92
- 6.3.5 USB 92
- 6.3.6 RS-485 93
- 6.4.1 Connectors 94
- 6.5.1 Relay Board Components 95
- 96 (122) 96
- 97 (122) 97
- 98 (122) 98
- 6.7 Updating Firmware 99
- 100 (122) 100
- Version 3.2 100
- LT-969 Copyright 2015 100
- 7 Adding Controllers 101
- 7.1 Adding a Controller 102
- Appendix 103
- 8.1 Specifications 104
- 8.1.6 Post Office Lock 105
- 8.1.7 Tamper Switch 105
- 8.1.8 Modem 105
- Lobby Control Unit Kit 107
- This chapter explains 111
- 9.1.1 Granting Access 112
- 9.1.2 Call Waiting Feature 112
- 9.1.3 Keyless Entry Codes 113
- 9.2.1 Granting Access 114
- 9.2.2 Keyless Entry Codes 114
- Limited Warranty 115
- International Warranty 115
- Conditions to Void Warranty 115
- Warranty Procedure 116
- Disclaimer of Warranties 116
- Out of Warranty Repairs 117
- Special Notices 118
- Type of Service 119
- Telephone Company Procedures 119
- Changes to Telephone Service 120
- Ringer Equivalence Number 120
- If Problems Arise 120
- Product Identifier 121
- Telephone Connection 121
- Equipment Failure 121
- Use With Alarm Auto Dialers 121
- 122 (122) 122
Prodotti e manuali riguardandi Sistemi di interfono Mircom TX3 Series
(54 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 2.558 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale